Turn your volume down to about half before you start, especially with headphones on.
- Left
- Right
- Both
The first sound plays in the left channel.
Each step plays a few soft beeps, twice: in the left channel, then the right, then both. After each one, say where you heard it.
On a phone, or a laptop with one speaker, both sides may come from the same place. That's normal, and the answer will say so.
Where did you hear it?
Heard nothing?
- Check the volume is turned up and nothing is muted, on the device and in the browser tab.
- Check the sound is going where you expect: your system's sound settings show which speakers or headphones are in use.
- On an iPhone or iPad, turn off silent mode. Sounds from a web page don't play while it's on.
- Bluetooth headphones and speakers can miss the first moment of a sound. The beeps play twice, so listen for the second time.
- Some browsers only allow sound after you press something on the page. If nothing plays, press the button again.
This test runs in your browser. Nothing is stored or uploaded.
This speaker test plays a sound in your left channel, then your right, then both, and asks where you heard each one. From your three answers it tells you whether left and right work, whether they’re swapped, or what’s going wrong. It works the same as a headphone test, an earbud check or a quick sound test for a pair of desk speakers. The whole check takes about half a minute.
How to run the left and right audio test
Before you press anything, turn your volume down to about half. That matters most with headphones on. A web page has no idea how loud you’ve set your device, and a sound that’s gentle on laptop speakers can be sharp in your ears.
- Put your headphones on the usual way round, or sit centred between your speakers.
- Press Start the test. A few soft beeps play in the left channel.
- Answer Left, Right, Both sides or Nothing. Say where you actually heard it, not where you think it ought to be.
- Do the same for the right channel and then for both together. The answer appears after the third reply.
If you missed a sound, press Play it again as often as you like before you answer. There’s no time limit.
The speaker test uses three short rising beeps rather than a voice saying “left” and “right”. A beep with a clean start is easy to place, and it doesn’t tell you which side you’re meant to hear, so nothing nudges your answer. Each set of beeps plays twice, because Bluetooth headphones and speakers often wake up a fraction late and swallow the first moment of a sound. If the first round seemed clipped or silent, listen for the second.
What a good speaker test result looks like
Stereo sound carries two separate channels, one for each side. On working headphones or a pair of speakers, the left beeps come only from the left, the right beeps only from the right, and the last set from both at once, sounding as if it sits in the middle of your head or between the speakers. That’s a passed stereo test, and the answer is Left and right both work.

Every answer the speaker test gives falls into one of three kinds:
- Okay: “Left and right both work”. Each sound came from the side it should, and both sides played together.
- Check this: the sound reached you, but not in the usual stereo way. Everything came from one side or from both, one side leaked into the other, or your answers didn’t fit together. Often there’s an ordinary reason, such as one earbud in or a phone’s single speaker, and the answer says what to look at.
- Not working: nothing played, a side stayed silent, a sound went missing, or left and right came out of the wrong sides. The answer names which, and what to try first.
What each speaker test answer means
Under every answer you’ll see What you heard, a row for each step marked as it should be or not. Here’s what the answers mean and what usually causes them.
Left and right are swapped
You heard the left beeps on the right and the right beeps on the left. Most often the headphones are simply on backwards: look for the small L and R printed inside the band or on the stem of each earbud. If they’re on correctly, the swap is happening somewhere else, perhaps in a sound app, a driver’s own control panel or speakers placed on the wrong sides of the desk. A related answer, The left sound came from the wrong side (or the right), means one sound crossed over while the other came from both sides. The same checks apply, plus the Mono Audio and balance settings further down.

One side makes no sound
The left side makes no sound (or the right) means one channel came from where it should and the other wasn’t heard at all. This is the classic “why is only one earbud working” fault. With a wire, push the plug fully home: a 3.5 mm plug that’s a millimetre short can drop a channel. With wireless earbuds, check that the quiet bud is charged and actually connected; taking both out, putting them back in the case and reconnecting sorts it out more often than you’d think. Then make sure the balance setting hasn’t been pushed to one end. If one side still stays silent, try another pair on the same device. If the second pair works, the fault is in the first pair.
A rarer version is Only one side works, and it played the wrong sound: one side is silent and the side that works is playing the other channel. Turn the headphones round, check both sides are connected and run it again.
All the sound came from one side
Here both sounds played, but both came out of the same side. If you’re wearing only one earbud, that’s normal: a single AirPod or earbud on its own plays both channels so you don’t lose half the music. If both are in, the other side may be disconnected, flat or half out, or Mono Audio may be on. This is a Check this answer rather than a failure for exactly that reason.
Every sound came from both sides
If left, right and both all sounded the same, your device is playing the two channels as one. That’s mono, and on a phone’s own speaker, a laptop with a single speaker or one Bluetooth speaker it’s simply how the hardware works. With headphones or a pair of speakers, it usually means Mono Audio is on in your accessibility settings. If your device has told the browser it only has one output channel, the answer mentions that too.

A sound went missing or leaked across
The left sound is missing (or the right) means one channel vanished and the other came from both sides. That pattern points at the connection: a plug that isn’t pushed fully in, a mono adapter, or an old cable or splitter that combines the channels. Unplug any adapter and connect directly if you can.
The left sound also came from the right (or the other way round) means one channel stayed on its own side while the other spread to both. On laptop speakers, a few centimetres apart and often firing downwards, the two sides really are hard to tell apart, so try headphones before you worry. With headphones, check the balance setting and that Mono Audio is off.
Your answers don’t match up
The test expects the “both” step to sound like the left and right steps added together. When it doesn’t, say you heard the left and the right on their own but only the left when both played, something is off: one side may be much quieter, cutting in and out, or you simply missed a beep. Run it again somewhere quiet and use Play it again freely. If the answers still don’t fit, a loose connection or a failing driver in one side is the likely cause, and it’s the same kind of fault that makes headphones keep cutting out.
And if you heard nothing at all, the answer is No sound came through. Check the volume and mute on the device and in the browser tab, check your system is sending sound where you expect, and on an iPhone or iPad turn off silent mode, because web page sounds don’t play while it’s on. Some browsers also refuse to play sound until you’ve pressed something on the page, so press the button again.
Testing headphones, earbuds and speakers
Wired headphones and the plug
A standard 3.5 mm headphone plug has three contacts: the tip carries the left channel, the ring next to it carries the right, and the long sleeve is the shared ground. A headset with a microphone adds a fourth contact, so its plug has an extra ring. When a plug sits halfway in the socket, the contacts line up with the wrong springs and you get odd results, such as one side gone or the two channels blended. That’s why so many of the answers above start with “push the plug all the way in”.

Bluetooth headphones and earbuds
Wireless earbuds each have their own battery and, on many pairs, their own connection, so one bud can drop out while the other carries on. Charge both, put them back in the case for a few seconds and reconnect. If the first beep of each round sounds cut off, that’s the connection waking up, not a fault. If your headset has a mic, test your microphone next.
How to test speakers on a laptop or PC
To test computer audio properly, first check which output is in use: on Windows it’s under Settings > System > Sound, and on a Mac under System Settings > Sound > Output. Neither will tell you if left and right are crossed. For desk speakers, sit in the middle and run the left and right speaker test as normal. For a laptop’s own speakers, expect a muddier result. Many laptops place two small speakers close together, and some have only one, so Every sound came from both sides or a leak answer is common and usually harmless. Plug in headphones to check the computer’s stereo output for certain.
The speaker test on phones and tablets
You can run a speaker test on an iPhone or Android phone, but think about what you’re testing. A phone that has one main speaker plays both channels from it, and the test will say so. Phones that play stereo through the bottom speaker and the earpiece together put the two sides only a few centimetres apart, so you’ll probably hear “both” for everything. The speaker test is most useful on a phone with headphones or earbuds connected. If you’ve paired your phone with a car by Bluetooth, the beeps play through the car’s speakers too, and the test can tell you whether the car’s left and right are working.
Is it the headphones or your ears?
When one side sounds quieter rather than silent, there’s a simple headphone check you can do yourself. Turn the headphones round so the left cup is on your right ear, or swap the earbuds, and listen again. If the quiet side follows the headphones, the headphones are the problem: earwax on an earbud’s mesh, a worn cushion that no longer seals, or a weak driver. If the quiet side stays with the same ear, the headphones are probably fine. This page isn’t a hearing test and can’t tell you anything about your ears. Earwax and ear infections can dull one ear, and both are treatable, but a sudden loss of hearing in one ear needs seeing to quickly: the NHS advice on hearing loss says to get an urgent GP appointment or call 111.
Where to find Mono Audio and balance settings
Mono Audio mixes left and right together so that someone with one earbud in, or hearing in one ear, doesn’t miss anything. It’s a useful accessibility setting, but switched on by accident it makes stereo vanish. Balance is the other setting worth checking: it shifts sound towards one side, and a slider nudged to one end will make the other side seem dead. Mono Audio sits in accessibility settings everywhere, which is not where most people look first; balance is there too on phones, and in sound settings on computers.
- Windows 11: Settings > Accessibility > Audio has the Mono audio switch. For balance, go to Settings > System > Sound, choose your speakers or headphones under Output, and in their output settings make sure the Left and Right channel levels match, as Microsoft’s guide to one-channel Bluetooth audio describes.
- Mac: System Settings > Accessibility > Audio has Play stereo audio as mono. The Balance slider is in System Settings > Sound, on the Output tab with your device selected.
- iPhone and iPad: Settings > Accessibility > Audio & Visual has Mono Audio and, below it, the Balance slider, as Apple’s iPhone guide shows. Older versions of iOS call the menu Audio/Visual.
- Android: Settings > Accessibility, then Audio adjustment on Pixel and many other phones, where you’ll find Mono audio and an audio balance slider. On a Samsung Galaxy they’re under Settings > Accessibility > Hearing enhancements.
Menu names shift a little between versions and phone makers. After you change anything, run the test again to confirm it worked.
What a speaker test in your browser can and can’t tell you
It can tell you which side each channel comes out of, whether a side is silent, and whether your system is playing in mono. That covers most of what goes wrong with headphones and speakers day to day.
It can’t tell you how loud anything is. A browser has no way of knowing your volume setting or how sensitive your headphones are, so the page never gives a sound level. It doesn’t judge sound quality, bass or distortion, and it plays two channels only, so it won’t check the rear or centre speakers of a surround system. Your answers do the hearing, which is why the test asks rather than measures. To hear how low or high a speaker goes, play a single tone at any frequency with the tone generator.
The sound is made in your browser as the page runs. The test doesn’t use your microphone, and nothing is stored or uploaded. If something failed and you want to work through the causes step by step, our fix guides are the place to start.
Questions people ask about the speaker test
Is a sound test the same as a speaker test?
For checking your own device, yes: both mean playing a sound to make sure it comes out where it should. This one goes a step further and checks each side separately. Be aware that “sound test” also turns up hearing tests and video game menus, which are something else.
Why beeps and not a voice saying left and right?
A voice tells you which side to expect, and people tend to hear what they’re told. Beeps don’t give the answer away, and their sharp start makes it easy to tell where they came from.
Does the sound test record me?
No. It only plays sound and never asks for your microphone. Your answers stay on the page while you use it; nothing is stored or uploaded.
Is it safe for my speakers and my ears?
The beeps are short and soft, and the first one is the quietest. The page keeps its own level well down, but your device’s volume decides how loud it really is, so start at about half and go up only if you need to. Don’t turn it up full to test anything.
Can I test the ear speaker on my phone?
Only if your phone uses it for media as well as calls. On phones that play stereo through the earpiece and the bottom speaker together, the test sound comes from both. On phones that keep the earpiece for calls, a web page can’t reach it.
Why do my laptop speakers sound like both sides at once?
Laptop speakers sit close together, often under the keyboard or along the bottom edge, and some laptops have only one. From where you sit, the two sides blur. Headphones give a clear answer about whether the laptop sends proper stereo.
Do I need to download a left right audio test MP3?
No. The page makes the sound itself as you go, so there’s nothing to download or play in another app. It also asks where you heard each sound, which a file can’t do.
How do I test my headphones for a Teams or Zoom call?
Run this test first to make sure both sides work. Then, since a call also needs your microphone and often your camera, check your speakers, mic and camera before a call with the pre-call check, and pick the same headphones in the call app’s own device settings.
Is this a hearing test?
No. It checks your speakers and headphones, and it assumes your ears are doing the listening. If you think your hearing has changed, talk to a GP or an audiologist.