Run a finger over every square
Each square turns green when it feels a touch. Use more fingers to check multi-touch.
- Areas
- Not started
- Fingers at once
- Not started
How this test decides
This test runs in your browser. Nothing is stored or uploaded.
This touch screen test fills your screen with squares and turns each one green the moment it feels a finger. Run a finger over all of them and anything that stays grey is a part of the screen that didn’t respond. At the end you get a plain answer that says where the problem is, and how many fingers the screen felt at once. It works on phones, tablets and touch screen laptops, with nothing to install.
How to test your touch screen
Open this page on the device you want to check, then:
- Press Start the test. The grid fills the screen. Each square is about 64 pixels across, roughly the size of a fingertip, so a phone gets about six squares across and a tablet or laptop many more.
- Run a finger slowly over every square, row by row, right to the edges and into the corners. A bar shows how many areas have responded and how many fingers are down.
- Put two, three or more fingers down together to check multi-touch.
- Press Done on the bar. The bar sits at the top and drops to the bottom while you work on the top half. Touches pass through it to the squares underneath, so it never hides part of the grid.
Go slowly. A quick swipe can jump over a square, and the test only counts places the screen actually reported a touch, so a missed square after a fast swipe tells you nothing. Use your fingers too: the test listens for touch only, so a stylus pen or a mouse won’t turn squares green. On an iPhone, Safari can’t hand the whole screen to a web page, so the grid covers the page instead. Turn the phone sideways or scroll so the toolbars hide to reach as much of the screen as possible.
Take off the case and screen protector first
A thick, lifted or cheaply made screen protector can stop touches registering, especially near the edges. So can a case with a raised lip that presses on the glass. Apple, Samsung and Nintendo all suggest removing the protector or case when a touch screen misbehaves. If you would rather not peel the protector off yet, run the test with it on first. A clean result means you can stop there. If a strip stays grey, take it off and test again before you blame the screen.

What your touch screen test result means
A square counts once the screen reports a touch anywhere inside it. The answer depends on how many squares never felt a touch.
- Okay: “Every area of the screen responded”. Every square felt a touch, so there is no dead spot big enough for a fingertip to find.
- Check this: “1 area didn’t respond” or “2 areas didn’t respond”. With so few left, you may simply have missed them. Press Test again and touch those squares slowly. You also see Check this as “The test wasn’t finished” when you touched fewer than half the squares. That is too few to say anything about the rest of the screen.
- Not working: more than two areas didn’t respond. The answer says where, for example “The squares that didn’t respond are in the top left corner and along the bottom of the screen”, and a small map shows them in grey.

The place names come from splitting the screen into nine parts: the four corners, the four sides and the middle. That wording is deliberate. “Along the bottom” or “in the top right corner” is what a repair shop needs to hear. And it is easier to say over the phone than a screenshot is to send. Keep the result on screen, or write it down, before you ask for a quote.

Testing multi-touch: how many fingers can your screen feel?
Phone and tablet screens follow more than one finger at once, which is how pinching to zoom and two-finger scrolling work. The multi-touch test is part of the same run: put several fingers down at once and the bar counts them. The result reports the most fingers felt at the same moment, as in “Up to 5 fingers were felt at once”. If you only ever used one finger, it says multi-touch wasn’t checked, rather than guessing.
Beside that, the test shows what the device reports about itself, for example “Your device says it can feel up to 10 fingers at once”. That figure comes from the browser, which passes on what the system says the touch hardware supports. It is a claim, not something this page has counted, which is why the test shows the two separately. If the screen says it can follow ten and you can only get it to count two, try again with your fingers spread apart. If it still stops at two, the touch layer may be damaged.
For everyday use, two fingers working properly anywhere on the screen is what matters. More fingers count for games, drawing and music apps, or a tablet shared by two people at once.

Touch screen dead spots: what they are and what causes them
A dead zone, or dead spot, is a part of the screen that shows the picture normally but doesn’t react when you touch it. Showing the picture and feeling your finger are separate jobs for separate parts, so one can fail while the other carries on. That is why a screen can look perfect and still ignore your finger along one edge.
Dead spots tend to have a shape that hints at the cause. A straight strip along one side is a common sight after a drop or a cheap screen replacement. A patch around a crack is damage to the touch layer itself. Grey squares only at the very edges, with the rest of the screen fine, point first at the protector or case. And a screen that works in one test and not the next, or only when it is cold or warm, can be a loose connector inside or the early signs of liquid damage.

A dead-zone test like this one finds the area, not the cause. It can’t see inside the device, so it can’t tell a damaged layer from a loose cable. What it can do is give you a repeatable answer: if the same squares stay grey after every step below, the fault is in the hardware.
When part of the screen doesn’t respond
If you are asking why your touch screen is not working in one area, go through these in order and run the test again after each one. They cost nothing and take a few minutes.
- Take off any screen protector or case that covers the edge.
- Clean and dry the screen and your hands. Water, grease and even a damp finger confuse the touch layer. Nintendo suggests a soft, dry cloth and no cleaning products, which is good advice for any screen.
- Restart the device. A touch controller that has stopped answering properly can come back after a restart.
- Check the settings. On a Samsung phone with a protector you want to keep, turn on Touch sensitivity, described below. On a laptop, check the touch screen hasn’t been turned off.
- Test again. If the same places stay grey, the touch screen needs repair. Apple’s advice for a screen that still isn’t working after these steps is the same: set up service.
No app or setting will fix a dead zone that survives all of that. On most phones and tablets the touch layer is bonded to the glass and the display, so a repair usually means replacing the whole screen. Ask the repairer to run the same test when the work is done, and before you pay.
Testing on a phone, tablet or laptop
iPhone and iPad
The test runs in Safari or any other browser on the device. Because a web page can’t take over the whole iPhone screen, the very top and bottom edges may sit under the browser’s bars. Turning the phone sideways and scrolling until the toolbars shrink gets you closer, and running the test in both orientations covers more of the edges. An iPad gives the page more room, and the grid there has more squares. The Apple Pencil is a pen, not a finger, so it won’t turn squares green.
Samsung and other Android phones
Chrome and Samsung Internet both run the test. Samsung phones have two built-in tools worth knowing about. If you use a screen protector, Samsung suggests turning on Touch sensitivity in Settings, Display, to help the screen feel your finger through it. Samsung also notes that non-genuine protectors and cases can affect touch, especially near the edges. And the Samsung Members app has phone diagnostics that include a touch screen check, which Samsung’s support page walks through. Running both, ours and Samsung’s, is a good way to be sure before you book a repair.
Laptops and touch monitors
If the test says “This test needs a touch screen” on a laptop you know has one, the touch screen may have been switched off. In Windows, right-click Start, open Device Manager, expand Human Interface Devices and look for HID-compliant touch screen. If it is disabled, right-click it to enable it, as Microsoft explains. There may be more than one entry, and each needs the same treatment. A touchpad is not a touch screen, so this test can’t check it. On a computer with no touch screen, the test offers the tests that do work there, and a Start anyway button if you know better.
Checking a second-hand phone or tablet before you buy
A dead strip is easy to miss in a five-minute look at a used phone. That’s because the seller’s home screen may never ask you to touch that part of the glass. Ask to open this page on the phone and run the test with the protector off, if the seller agrees. It takes a minute, and a dead strip is something you want to find before you hand over the money, not after.
While you have the phone in your hand, check the display for dead pixels and check the screen’s colours and resolution, which find faults in the picture that a touch test can’t. A speaker test and a mic test cover the two parts that are hardest to judge in a noisy café. None of these needs an account or an app.
What a touch screen test in the browser can and can’t tell you
This screen touch test checks one thing well: whether each part of the screen reports a finger, and how many fingers it reports at once. It doesn’t measure how hard you press, how quickly the screen reacts or how precisely it places your finger, and it can’t see cracks, bright spots or faults in the picture. A square about 64 pixels across is fingertip size, so a dead patch smaller than that might sit inside a square that still turned green from its edge.
It also can’t tell your touches from ones the screen invents, which is the first question below. The test runs entirely in your browser. Nothing is stored or uploaded, as our privacy page explains.
Questions people ask
What is ghost touch, and can this test show it?
Ghost touch is a screen reacting to touches nobody made: apps opening by themselves or typing on its own. This test doesn’t detect it, because it can’t tell a phantom touch from a real one. What you can do is watch: if squares turn green while your hands are off the screen, or the finger count goes higher than the fingers you have down, the screen is reporting touches you didn’t make, and that is worth telling a repairer.
Can a screen protector stop touches registering?
Yes. A thick protector, one that has lifted at the edge or one with dust or air bubbles under it can stop the screen feeling your finger. Nintendo’s own support says a protector can cause touch screen problems, and Apple and Samsung both suggest removing it when touch misbehaves. Test with it off before deciding the screen is at fault.
Can a touch screen dead zone be fixed?
If it goes away with the protector off, after cleaning or after a restart, it was never a dead zone. If the same squares stay grey after all of that, the fault is in the hardware and needs a repair, which on most phones means replacing the screen. Apps that claim to calibrate or fix dead zones can’t repair a damaged touch layer.
Why does the test say my device has no touch screen?
Your browser isn’t reporting one. Either the device has no touch screen, which is true of most desktop monitors and many laptops, or it has one that has been turned off. On Windows, check Device Manager under Human Interface Devices. If you are sure the screen supports touch, press Start anyway.
Can I test my laptop’s touchpad here?
No. A touchpad moves the pointer the way a mouse does, and the test counts touches on the screen only. To check that a touchpad’s clicks register, a mouse test is the better fit.
Why did a fast swipe miss squares?
The screen reports your finger’s position many times a second, and the test only counts the places it reported. A very fast swipe can cross a square between two reports, so that square stays grey. Go over any grey squares again, slowly, before deciding they are dead.
How many fingers should my screen detect?
There is no single right number. The test shows what your device says it supports, and what it actually felt during your run. If those are close, or the count is at least as many fingers as your apps need, the multi-touch is working.
Can a touch screen wear out?
Not from ordinary tapping, the way a button wears out. The touch layer is under the glass and has no moving parts. Touch faults usually come from a drop, pressure, liquid or a connector working loose, and a worn or scratched screen protector can also make touch feel less reliable.
Is anything recorded or uploaded?
No. The test runs in your browser and only keeps the grid of squares while the page is open. Nothing is stored or uploaded.