Skip to the content

Tone generator

Free online tone generator: play any frequency from 20 Hz to 20 kHz as a sine, square, saw or triangle wave. It starts quiet.

  • Nothing is stored or uploaded
  • Free, no sign-up, nothing to install
  • Chrome, Edge, Firefox and Safari
Hz

Any frequency from 20 Hz to 20 kHz. Type a number, move the slider or pick one below.

Quick picks
Wave

Start quiet and turn it up slowly. Very high and very low tones can be loud before they are easy to hear. Stop if it hurts.

The volume starts at 25% every time. The page can't tell how loud your device is, so keep the device's own volume low too.

Can't hear the tone?
  1. Check the volume is turned up and nothing is muted, on the device and in the browser tab.
  2. On an iPhone or iPad, turn off silent mode. Sounds from a web page don't play while it's on.
  3. Phone and laptop speakers can't play very low tones, so you may hear little or nothing below about 200 Hz. Headphones go lower.
  4. Most adults can't hear tones above about 15 kHz, and hearing at the top of the range fades with age. That's normal.
  5. Bluetooth headphones and speakers can miss the first moment of a sound and start a little late. Give it a second.
  6. Some browsers only allow sound after you press something on the page. If nothing plays, press the button again.
How the tone is made

The tone is made in your browser as you listen. No sound files are downloaded, and nothing is recorded.

It plays any frequency from 20 Hz to 20 kHz. The slider is spaced like the keys of a piano, so each step up multiplies the frequency by the same amount. With the slider selected, the arrow keys move it a small step, and Page Up and Page Down roughly double or halve the frequency.

Even at 100%, the page sends the tone at 50% of full strength. Square waves play at 71% of the volume you set, so no wave shape carries more energy than a sine. Square and saw waves can still sound louder, because they include higher notes that the ear picks up easily.

A browser can't tell how loud your speakers or headphones are, so the page never states a sound level. Your device's own volume decides how loud it is.

This tool runs in your browser. Nothing is stored or uploaded.

This online tone generator plays one steady tone at any frequency from 20 Hz to 20 kHz, as a sine, square, saw or triangle wave. It opens on 440 Hz, the note orchestras tune to, with the volume at 25%. A tone generator is sometimes called a frequency generator or an Hz generator. The names all mean the same thing: you pick a pitch, and the page plays exactly that pitch until you stop it.

How to use the tone generator

Turn your device’s own volume down first, then press Play the tone. Change anything while it plays and you’ll hear the change straight away. Press Stop the tone when you’re done.

The tone generator set to 440 Hz: a play button beside the frequency, a sine wave drawn on a dark panel, a frequency slider from 20 Hz to 20 kHz, quick picks, four wave shapes and the volume at 25%.
As it opens: 440 Hz, a sine wave, volume at 25%. It starts quiet every time.

There are three ways to choose a frequency:

  • Type it. Enter any number of hertz, to a tenth of a hertz: 440, 261.6, “1k” or “1.5 kHz” all work. In the box, the up and down arrow keys move it 1 Hz at a time. Anything below 20 Hz or above 20 kHz is set to the nearest end, and the page tells you so.
  • Slide it. The slider is spaced like the keys of a piano, so moving it the same distance always changes the pitch by the same musical step. That gives the low notes as much room as the high ones. On an evenly spaced slider, everything below 1,000 Hz would be crammed into the first few millimetres. With the slider selected, the arrow keys move about a tenth of an octave, and Page Up and Page Down roughly double or halve the frequency.
  • Pick one. The quick picks are 50, 440, 1,000 and 10,000 Hz: a low hum, the tuning note, the standard test tone and a high hiss.

Under Wave you choose the shape of the tone, and Volume sets how strongly the page sends it. The volume starts at 25% on every visit, whatever you used last time, because nothing is remembered between visits.

What different frequencies sound like

Frequency is how many times a second the sound wave repeats, measured in hertz (Hz). More hertz means a higher pitch, and every doubling is one octave up. The range people usually quote for human hearing is 20 Hz to 20 kHz, which is why the generator covers exactly that span. Only young, healthy ears reach both ends, though.

A 20 Hz to 20 kHz scale in octaves: sub-bass, bass, voices and treble. Blue dots mark 50 Hz, 440 Hz, 1 kHz and 10 kHz. Brackets show phones play little below 200 Hz and the top end fades with age.
The range the generator covers, spaced the way the slider is. The blue dots are the quick picks: 50, 440, 1,000 and 10,000 Hz.
  • 20 to 60 Hz, sub-bass. The rumble under film soundtracks and electronic music. Down here you feel a tone through a good subwoofer as much as you hear it, and small speakers give you almost nothing.
  • 60 to 250 Hz, bass. Bass guitar, kick drums and the body of a man’s voice. The 50 Hz quick pick sits just below this zone and sounds close to the hum from electrical mains in Britain and Europe. In North America the mains hum is 60 Hz.
  • 250 Hz to 4 kHz, the middle. Where voices and most instruments live, and the part of the range your ears follow most closely. 440 Hz is the A above middle C. 1,000 Hz is the plain beep used as a reference tone in audio and broadcast work. It’s also a good place to start if you just want to hear something.
  • 4 kHz upwards, treble. The crispness of consonants, cymbals and birdsong. At 10 kHz a tone is a thin, high whistle. Further up it becomes hard to locate and, for many adults, hard to hear at all.

Looking for an Hz test sound?

If you searched for an “Hz test” to hear a particular frequency, a bass note or a subwoofer test tone, you’re in the right place: type the number and press play. If you meant the hertz of your monitor, how many times a second the picture updates, that’s a different thing entirely. Use the refresh rate test instead.

Sine, square, saw and triangle waves

At the same frequency, all four shapes play the same note, but they sound noticeably different. The difference comes from harmonics: quieter tones at two, three, four or more times the main frequency that ride along with it. Your ear hears them as the character of a sound, which is why a flute and a violin playing the same note don’t sound alike.

Two cycles each of four waves: sine, a smooth curve; square, jumping between high and low; saw, rising in a slope then dropping straight down; and triangle, rising and falling in straight lines.
Same pitch, four shapes. The sharper the corners, the more harmonics the wave carries.

Sine is the purest tone there is: one frequency and nothing else. It sounds soft and round, a little like a tuning fork or a whistle. Use it for tuning, for checking speakers and whenever you want to know exactly which frequency you’re hearing.

Square jumps between two levels. It adds the odd harmonics (three, five, seven times the frequency and so on). That gives it a hollow, buzzy sound, close to an old video game or a clarinet’s low notes.

Saw climbs steadily and then drops. It carries every harmonic, odd and even, so it’s the brightest and harshest of the four. It’s the raw material of many synthesiser sounds, and closer to a bowed string or a brass instrument.

Triangle rises and falls in straight lines. Like the square it has only odd harmonics, but they fade away much faster, so it sounds only slightly brighter than a sine.

Why square and saw waves can sound louder

Bar charts of each wave’s first nine harmonics. Sine has only the first. Square has the odd ones and saw has all of them, both shrinking steadily. Triangle has the odd ones, shrinking very quickly.
The first bar is the note you chose; the others are its harmonics. This is why a square or saw wave sounds brighter, and often louder, than a sine at the same setting.

Those extra harmonics reach up into the range where hearing is most sensitive, so a square or saw wave can sound louder than a sine at the same volume setting. The generator allows for part of that. It plays the square wave at about 71% of the volume you set, so that no shape carries more energy than a sine. They can still sound louder, so turn down when you switch shapes.

Why you might not hear the tone

Phone and laptop speakers can’t play low tones

Low notes need a lot of air moved slowly. The speaker in a phone or a thin laptop is too small to do that. Below about 200 Hz they give you little or nothing, which is why a phone can’t play 30 Hz however far you turn it up. What you may hear instead is a faint buzz from the speaker straining, or from harmonics if you’ve chosen a square or saw wave. Headphones go much lower, because they only have to move the small pocket of air in your ear canal. A proper subwoofer goes lower still.

A sketch of loudness against frequency. The headphones line stays level from 20 Hz to near 20 kHz. The phone speaker line matches it in the middle but falls away steeply below a few hundred hertz.
A sketch, not a measurement. A phone speaker is too small to move much air, so low tones fade out long before they reach the bottom of the range.

High tones fade with age

The top end of hearing drops as we get older, gradually and usually without being noticed, so most adults hear little above about 15 kHz. If 10 kHz is clear and 16 kHz is silence, that’s normal. Small speakers and some earbuds roll off near the top too, so silence at 18 kHz may be the speaker as much as you.

Silent mode, Bluetooth and the play button

If nothing plays at any frequency, check the obvious first. On an iPhone or iPad, silent mode stops sounds from web pages. Make sure the volume is up and the tab isn’t muted, and that sound is going to the output you expect. Some browsers only allow sound after you press something, so press play again. Bluetooth headphones and speakers can start a moment late, so give it a second. The tone also stops if you switch to another tab or app, and comes back when you press play.

What people use a tone generator for

Tuning to a 440 Hz tone

The A above middle C is set at 440 Hz by an international standard, ISO 16, and it’s the note an orchestra tunes to. Play it as a sine and tune your A string by ear until the slow wobble between the two sounds disappears. Middle C itself is about 261.6 Hz. Some musicians prefer to tune to 432 Hz; that’s simply a different reference pitch, slightly lower, and this page makes no claim that either one is better for you. For everyday tuning, a clip-on tuner will show you how far off you are, which a tone can’t.

Testing speakers and subwoofers with a tone generator

A sine wave is the cleanest bass test there is. To find how low a speaker or subwoofer goes, start quiet at about 100 Hz and step down slowly. Somewhere the tone thins out and then disappears; that’s roughly where the speaker gives up. Treat it as a listening check, not a measurement. Your room boosts some low notes and swallows others, so moving your chair can change what you hear. Keep the volume modest: a speaker pushed hard with a low tone can be damaged, and you won’t always hear it struggling before it does. If you’re not sure both sides work, check left and right on your speakers or headphones first.

Finding a rattle or buzz

A loose car door panel, a picture frame or a desk drawer will buzz along with one particular low note. Play a sine at a low volume and slide slowly through the range from about 40 to 200 Hz. When something starts to buzz, stop, hold that frequency, and press on the panels nearby until the buzz goes quiet. That’s the one to fix.

Finding the highest tone you can hear

Out of curiosity, you can wear headphones, set a low volume and move upwards from 10 kHz until the tone vanishes. Don’t turn the volume up to chase it: a tone you can’t hear can still be strong. Bear in mind that the result depends on your headphones as much as your ears, so this isn’t a hearing test. If you’re worried about your hearing, an audiologist can test it properly.

Describing tinnitus to a doctor

Some people with tinnitus use a tone to find something close to the pitch they hear, so they can describe it to a doctor or audiologist. If you try it, keep the volume very low. Compare an octave up and down as well, since notes an octave apart are easy to confuse. The page does not treat, mask or relieve tinnitus. The NHS tinnitus page says when to see a GP about it, including straight away if it beats in time with your pulse.

Using a tone generator safely

Very high and very low tones can be loud before they’re easy to hear, so the generator is built to start low. The volume opens at 25% every time. The slider follows a curve that gives you fine control at the quiet end, so 25% plays at a sixteenth of the most the page will send. Even at 100%, the page sends the tone at only half of full strength.

None of that sets how loud the sound actually is. A browser can’t tell what your device’s volume is or how sensitive your headphones are, so the page never shows a sound level, and your own volume control has the final say. Keep it low, turn up slowly and stop if anything hurts. The NHS advice on hearing loss puts it simply: the volume should be just high enough for you to hear comfortably.

What this tone generator can and can’t do

It plays one tone at a time, at any frequency from 20 Hz to 20 kHz, in four shapes. It doesn’t sweep through frequencies on its own: move the slider by hand, or use Page Up and Page Down to jump an octave. Nor can it play two tones together or send a tone to one side only, and there’s no sound file to download or link to share. It measures nothing, so it can’t give a speaker’s frequency response or a level in decibels.

The tone is made in your browser as you listen. No sound files are downloaded, no microphone is used, and nothing is stored or uploaded.

One more thing: a “tone generator and probe” sold in hardware shops is an electrician’s tool for tracing wires through a wall. It shares the name and nothing else.

Questions people ask about the tone generator

Is it safe to play loud tones?

Keep them quiet instead. The page starts at 25% and never sends a full-strength signal, but it can’t know how loud your device is, so keep that low too. Very high and very low tones can be loud before you notice them. Stop if it hurts.

Why does nothing happen when I press play?

Check silent mode on an iPhone or iPad, the volume and mute on your device and the tab, and which output your system is using. Some browsers need a second press before they allow sound. If only some frequencies are silent, it’s probably your speaker’s range, explained above.

Can I play more than one tone at once?

No, it plays one tone at a time. To hear two notes against each other, you’d need a second device or an app made for that.

Can I tune an instrument with this?

Yes, by ear. Play the reference note as a sine, 440 Hz for A, and adjust until the beating between the tone and your string slows to nothing. A tuner is quicker if you just want to know whether you’re sharp or flat.

Can a tone push water out of my phone speaker?

This page makes no such claim, and we haven’t found independent evidence that a tone from a web page does it. Follow your phone maker’s advice for a wet phone instead; for an iPhone, Apple’s page on liquid-detection alerts explains how to dry it safely.

Can I download the tone?

No. The tone is made live in your browser and there’s no file to save. If you need a recording, an audio editor can generate a tone and export it.

Is there a frequency sweep?

Not on this page. Drag the slider slowly to sweep by hand, or select it and hold an arrow key to climb in small steps.

Why do square and saw waves sound louder?

They carry harmonics, higher notes that land where hearing is most sensitive. The page already plays the square wave lower so it carries no more energy than a sine, but the ear still picks up those extra notes. Turn down a little when you switch.

Is 432 Hz better than 440 Hz?

They’re two reference pitches, about a third of a semitone apart. 440 Hz is the international standard; some musicians like the slightly lower 432 Hz. Claims that one is better for health aren’t something this page makes or supports.